Deformation and Fracture Mechanics of Engineering MaterialsThis Third Edition of the well-received engineering materials book has been completely updated, and now contains over 1,100 citations. Thorough enough to serve as a text, and up-to-date enough to serve as a reference. There is a new chapter on strengthening mechanisms in metals, new sections on composites and on superlattice dislocations, expanded treatment of cast and powder-produced conventional alloys, plastics, quantitative fractography, JIC and KIEAC test procedures, fatigue, and failure analysis. Includes examples and case histories. |
From inside the book
Results 1-3 of 55
Page 364
... plate containing a surface flaw ( arrester orientation ) might be expected to exhibit somewhat higher toughness than the same material prepared in the form of an edge - notched plate , where the crack would propagate parallel to the ...
... plate containing a surface flaw ( arrester orientation ) might be expected to exhibit somewhat higher toughness than the same material prepared in the form of an edge - notched plate , where the crack would propagate parallel to the ...
Page 411
... Plate Specimen Temperature σys Orientation ( ° C ) KIC ( MPa ) ( MPaVm ) L - T 21-32 525-540 22-27 " T - L ?? 530 ... Plate L - T " 460-510 33-41 " " 1 T - L 450-510 29-38 " 1 " 1 S - L " 430-440 25-28 7075 - T651 Plate L - T 21-32 515 ...
... Plate Specimen Temperature σys Orientation ( ° C ) KIC ( MPa ) ( MPaVm ) L - T 21-32 525-540 22-27 " T - L ?? 530 ... Plate L - T " 460-510 33-41 " " 1 T - L 450-510 29-38 " 1 " 1 S - L " 430-440 25-28 7075 - T651 Plate L - T 21-32 515 ...
Page 413
... Plate 93 Plate 56 Plate 120-140 Plate 100 Plate 80-88 " 45-58 Forging 75-95 " 72 ( Mill anneal plate ) 112 " 96 ( Recryst . anneal plate ) " 77-97 70-105 For additional K data , see reference 177 and Fig . 10.32 . 1.8-2.1 0.21-1.30 2.7 ...
... Plate 93 Plate 56 Plate 120-140 Plate 100 Plate 80-88 " 45-58 Forging 75-95 " 72 ( Mill anneal plate ) 112 " 96 ( Recryst . anneal plate ) " 77-97 70-105 For additional K data , see reference 177 and Fig . 10.32 . 1.8-2.1 0.21-1.30 2.7 ...
Contents
Tensile Response of Materials | 3 |
Elements of Dislocation Theory | 49 |
Slip and Twinning in Crystalline Solids | 81 |
Copyright | |
16 other sections not shown
Common terms and phrases
aluminum alloy applied stress associated ASTM ASTM STP atom behavior brittle Burgers vector ceramics Chapter Charpy component composite corrosion crack growth rate crack length crack tip craze creep crystal cycles cyclic da/dN decrease depends ductility elastic embrittlement engineering example failure fiber FIGURE flaw fracture mechanics fracture surface fracture toughness given grain boundaries hardening hydrogen increasing KIEAC Kmax ksivin lattice load martensite material matrix Mech metallurgical microstructure modulus MPaVm Note occur orientation particles phase plane-strain plastic deformation plastic zone plate polymer R. W. Hertzberg ratio region relation relative Reprinted with permission response result sample screw dislocation Section shear stress shown in Fig slip plane slip systems solid solution specimen stacking fault energy steel alloys strain rate stress concentration stress field stress intensity factor stress level stress-strain curve striation superalloys thickness Trans transition temperature twin values yield strength