Ceramography: Preparation and Analysis of Ceramic Microstructures"Ceramography" provides detailed instructions on how to saw, mount, grind, polish, etch, examine, interpret and measure ceramic microstructures. This new book includes an atlas of ceramic microstructures, quantitative microstructural example problems with solutions, properties and data tables specific to ceramic microstructures, more than 100 original photographs and illustrations, and numerous practical tips and tricks of the trade. An excellent reference guide for technicians in quality control and R&D, process engineers in ceramic manufacturing, and their counterparts in engineering firms, national laboratories, research institutes, and universities. |
From inside the book
Results 1-5 of 54
Page 2
... mentioned but not described in great detail, including crystallography, electron microscopy, hardness, and ceramic ... shown in Fig. 1.1. Crystallography. Crystallography, the study of crystal structures and lattice spacing, is an ...
... mentioned but not described in great detail, including crystallography, electron microscopy, hardness, and ceramic ... shown in Fig. 1.1. Crystallography. Crystallography, the study of crystal structures and lattice spacing, is an ...
Page 19
... shown in Fig. 3.1(a). A resin-bonded diamond blade may be advantageous for some specimens. Use a load of approximately 5 to 10 N (500 to 1000 gf) and a blade rotation rate of 2000 to 5000 rpm for dense ceramics. Use 1 N and 500 rpm for ...
... shown in Fig. 3.1(a). A resin-bonded diamond blade may be advantageous for some specimens. Use a load of approximately 5 to 10 N (500 to 1000 gf) and a blade rotation rate of 2000 to 5000 rpm for dense ceramics. Use 1 N and 500 rpm for ...
Page 20
... shown in Fig. 3.2(b). Sawing should always be done in a way that minimizes damage to the specimen, such as overheating, dislocations, deformation twinning, and cracking on or near the sawed surface. While ceramics are usually not as ...
... shown in Fig. 3.2(b). Sawing should always be done in a way that minimizes damage to the specimen, such as overheating, dislocations, deformation twinning, and cracking on or near the sawed surface. While ceramics are usually not as ...
Page 23
... shown schematically in Fig. 3.4 (Ref 2). The resins are described in Table 3.1. 4. Fill the outer die to 5 mm below the rim with phenolic resin or a phenolic premold disc. Level the phenolic powder by tamping it with the upper ram ...
... shown schematically in Fig. 3.4 (Ref 2). The resins are described in Table 3.1. 4. Fill the outer die to 5 mm below the rim with phenolic resin or a phenolic premold disc. Level the phenolic powder by tamping it with the upper ram ...
Page 24
... shown on the gage is usually the air pressure supplied to the press, not the die compression. Table 3.2 shows the ... mentioned previously, Upper ram Die cylinder Lower ram Label A. B. C. Specimen Fig. 3.4 Cross section of a loaded ...
... shown on the gage is usually the air pressure supplied to the press, not the die compression. Table 3.2 shows the ... mentioned previously, Upper ram Die cylinder Lower ram Label A. B. C. Specimen Fig. 3.4 Cross section of a loaded ...
Other editions - View all
Common terms and phrases
abrasive acid acoustic microscopy acrylic Al2O3 thin section alumina analysis approximately ASM International ASTM beam ceramics Ceramics and Glasses ceramographic Chapter chemically etched coefficient color compression crack cross section crystal cubic diameter diamond edge electric encapsulation epoxy etchant etching methods filter first flat fracture furnace grain boundaries grain size gray levels grinding and polishing heat image analyzer indentation interference layer Köhler illumination lens liquid load lubricant magnification Materials Handbook mean grain Mean GS measured metal MgAl2O4 micrograph microindentation hardness microstructure mold monoclinic objective optical oxide particles pixel plastic platen polarized Polaroid pores porosity Prep ramic Reagent reflected refractive index Relief polish replica room temperature rotated Scanning electron microscope secondary phases shown in Fig Silicon carbide sintering slide specific specimen spinel sputter coated step Subroutine 5.1 Testing TiO2 tion toughness tube ultrasonic USA Telephone vacuum wavelength x-ray zirconia ZrO2 µm Fig
Popular passages
Page 154 - The coefficient of variation is the ratio of the standard deviation to the mean...
Page 202 - Standard Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials.
Page 68 - EM Levin, CR Robbins, and HF McMurdie, Phase Diagrams for Ceramists— 1969 Supplement, The American Ceramic Society, Columbus, Ohio, 1969.
Page 203 - American Society for Testing and Materials, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. (1) ASTM D-93-79 or D-93-80, "Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester,
Page 68 - Evaluation of Zircon Brick for Steel Ladle Slag Lines," Am. Ceram. Soc. Bull. 63[7], 880-883 (1984). 14. EM Levin, CR Robbins, and HF McMurdie, "Phase Diagrams for Ceramists,
Page 187 - Richerson, Modern Ceramic Engineering: Properties, Processing and Use in Design, 2nd ed., Marcel Dekker, Inc., New York, 1992.
Page 7 - Materials Science and Engineering. An Introduction, 5th Ed.
Page 202 - E 6 Definitions of Terms Relating to Methods of Mechanical Testing...